jahaax.blogg.se - Gale subwoofer manual

#Gale subwoofer manual how to#
#Gale subwoofer manual update#

Do not work on electrically live parts.When unplugging it, hold the plug, not the wire. Be sure that it is properly grounded before use. The power cord must be plugged into approved bases.Do not use the units for any purpose other than soldering or rework.It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion Repairs should only be performed by a JBC-authorized technical service.Press the new fuse into the fuse holder and replace it in the station.Pull off the fuse holder and remove the fuse.

Replace any defective or damaged pieces.

Rusty and dirty surfaces reduce heat transfer to the solder joint.

Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation.

Periodically check that the metal parts of the tool and stand are clean so that the station can detect the tool status.

Alcohol can only be used to clean the metal parts.

Use a damp cloth to clean the casing and the tool.

Clean the station screen with a glass cleaner or a damp cloth.

Maintenanceīefore carrying out maintenance, always switch the device off and disconnect it from the mains.

Remove the drawer from the Splashguard.

Press back the tap (1) to remove the Cleaning System 2).

Use a pliers if necessary Changing the Tip Cleaning System Find the model that best suits your soldering needs on Changing Gripsįirst, put the slide-on tabs into the new grip, then push the grip with the tabs onto the handle. The Nano Handle NT115 and the Adjustable Nano Tweezers AN115 work with C115 cartridges. It is essential to insert the cartridges as far as the reference ring for a proper connection. Use the holes to rotate the cartridges for a proper alignment. Push the cartridge into the handle until the mark”. Place tne cartridge into the extractor slot (1) and pull the handle to remove them (2). Save time and change cartridges safely without having to switch the station off. Once in position press and hold the pedal to activate the tool and perform the soldering. Note: The inactive tool prevents the component from heating up prematurely. Use the tool to position the component on the previously tinned pad. The use of JBC’s DPM Solder Paste Dispenser is recommended. Īpply the solder paste amount needed to solder the new chip component. For this operation JBCs Desoldering Station is needed.

Ĭlean the pads with the desoldering tool DS360-A. Once the pedal is released the tool enters en Hibernation Mode and cools down. Lift the tool from the holder, press and hold the pedal to activate the tool and desolder the component. In the peripherals menu for the Pedal Activation Mode choose between “pressed” and “released”. As a result, tip life increases by 5.Ĭonnect pedal P-405 to the same port where the Nano Tweezers are connected.

This allows the user to work at a lower temperature. This revolutionary technology is able to recover tip temperature extremely quickly.

#Gale subwoofer manual how to#

Press INFO for failure description, the type of error and how to proceed. The following icons will be displayed on the screen’s status bar.

#Gale subwoofer manual update#

Insert a USB flash drive into the USB-A connector to save your soldering process in csv format.ĭownload the JBC Update File from Insert the USB flash drive with the file downloaded to the station. Manage your whole soldering process remotely in real time.

Get greater quality and control in your production.

Up to 25 fully conﬁ gurable soldering proﬁ les can be stored.

Designed to avoid thermal shock when soldering Ceramic Chip components like MLCC, this new and unique feature allows controlling the heating ramp up rate of the tool to gradually increase the temperature of the component through all the phases of the soldering process.

This helps you decide how to adjust your process or which tip to use to obtain the best quality soldering.

It provides detailed graphics of tip temperature and power delivery in real time during solder joint formation for analysis purposes.

Station troubleshooting available on the product page at Advanced Functionalities